Home| Siegetek GEN 3 10.78 9-tooth DSG Gear set for V2/V3

Manufactured by: Siegetek Concepts

Siegetek GEN 3 10.78 9-tooth DSG Gear set for V2/V3

Manufactured by: Siegetek Concepts

Siegetek GEN 3 10.78 9-tooth DSG Gear set for V2/V3

Weight: 0.13 lb

Model: GS-RP-C2

$135.00
$135.00
Sale
Out of stock
product details

Siegetek Concepts is an innovative, USA-based company that produces the highest quality Gear sets in the world. These new Gen 2 sets are no exception, and have been even further enhanced. For Airsofters who want to squeeze out every last drop of performance into their AEG, Siegetek gears are a must-have.

This Gear set will give you a ridiculously high rate of fire. Please keep in mind that because there is an extra tooth on the Sector, spring pairing is of heightened importance. Keep your piston light, your spring strong, and your ROF moderate to avoid mistiming.

The following enhancements are described by RiotSC himself:

"These Gen 2 gears use a new 2-piece design compared to the original version's 5-piece. The material has also been updated to even stronger nickel chromoly steel as opposed to the chromoly steel used in the original version. The surface finish has been changed to manganese phosphate from the original black oxide. Manganese phosphate provides better wear resistance and lubricant retention properties."

Installing a DSG Gearset requires technical expertise and fine tuning of the Gearbox. I had to do a lot of research and read voraciously before I could unlock the full potential of these gears. The official DSG instruction manual is a good start: http://www.siegetek.com/instructions/cyclone.pdf

Use of the Siegetek G4 pinion gear is strongly recommended.

product details

Siegetek Concepts is an innovative, USA-based company that produces the highest quality Gear sets in the world. These new Gen 2 sets are no exception, and have been even further enhanced. For Airsofters who want to squeeze out every last drop of performance into their AEG, Siegetek gears are a must-have.

This Gear set will give you a ridiculously high rate of fire. Please keep in mind that because there is an extra tooth on the Sector, spring pairing is of heightened importance. Keep your piston light, your spring strong, and your ROF moderate to avoid mistiming.

The following enhancements are described by RiotSC himself:

"These Gen 2 gears use a new 2-piece design compared to the original version's 5-piece. The material has also been updated to even stronger nickel chromoly steel as opposed to the chromoly steel used in the original version. The surface finish has been changed to manganese phosphate from the original black oxide. Manganese phosphate provides better wear resistance and lubricant retention properties."

Installing a DSG Gearset requires technical expertise and fine tuning of the Gearbox. I had to do a lot of research and read voraciously before I could unlock the full potential of these gears. The official DSG instruction manual is a good start: http://www.siegetek.com/instructions/cyclone.pdf

Use of the Siegetek G4 pinion gear is strongly recommended.

Customer Reviews

Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
S
S.L.

I recently purchased and installed this DSG set, and would like to share my experience to aid whoever I can to make installation as painless as possible. For my build, the entire system worked and fed, flawlessly only after 3 hours of installation. I strongly recommend buying everything siegetek pinion up. And then use Lonex for the rest. I find that the meshing of everything eased the installation, took out the second guessing, as well as prolonged the lifetime of the overall system. Since its assembly it has ran 3000rds without issue or failure (lucky so far XD). A few things to note, the bevel gear has the new design of the AR latches and the horizontal gear blended together, as shown in the picture. A stock AR latch may seem to work by hand testing, but it will not work when the system begins to actually cycle. To get the ARL to engage correctly. Replace it with a steel lonex one, and grind off about .5mm of material off the tip of the latch, the latch will be less pointy and engage correctly. When installing the lonex red piston, I swisscheesed the entire assembly down to 17.4 grams with the head. Paired with a guarder sp150, the system cycles fine with no PME. If you plan to use a stronger spring I'm assuming your piston assembly can be left heavier. Overall, I recommend buying all lonex and siegetek parts right here from Brill Armory, it saved me a lot of time, second guessing, and money in the long run.

manufacturers

ACETECHAction ArmyActionSportGa...Airsoft Innov...Airsoft MutationAirsoft PartsAlphaWireAztech Innova...BB BastardBioshotBlackTalon Co...BRILL ARMORYCHEMIS CYMADKT BrandDream ArmyEagle6 AirsoftEcho 1ElementElite ForceEmei Landarms...EPeS Airsoft Field Limit T...FPS SoftairGATE ElectronicsGuarderGungineer Air...JefftronLambda AirsoftLaylaxLCTLonexMaekiiiMaple Airsoft...ModifyNorthern Hurr...PDIPerun AirsoftPolarStar Air...PPSProfessional ...ProWinRetro ARMSRocket AirsoftSapporo Preci...ScatterplotSHSSiegetek Conc...SlongSolinkSparkLabsSpring-TekSuper LubeSuper ShooterT238TruSight Airs...W.S. Deans Co.Warhead Indus...XcortechZCI